Skip to main content

Acrylic Emblem Light



This Blog will illustrate you how to make Color changing Emblen light using PWM of arduino.
using this you can make your emblems look more attractive.


Components Required

1> Arduino UNO
2> 12V RGB led strip
3> 2N2222 Transistor
4> 10K ohm Resistor
5> Jumper Wires
6> Small Breadboard
7> Acrylic Engraved Emblem
8>IC7805 Power Regulator

Circuit Diagram 

Arduino Code

const int greenPin = 10;
const int bluePin = 9;
void setup() {
// Start off with the LED off.
setColourRgb(0,0,0);
}
void loop() {
unsigned int rgbColour[3];
// Start off with red.
rgbColour[0] = 255;
rgbColour[1] = 0;
rgbColour[2] = 0;
// Choose the colours to increment and decrement.
for (int decColour = 0; decColour < 3; decColour += 1) {
int incColour = decColour == 2 ? 0 : decColour + 1;
// cross-fade the two colours.
for(int i = 0; i < 255; i += 1) {
rgbColour[decColour] -= 1;
rgbColour[incColour] += 1;
setColourRgb(rgbColour[0], rgbColour[1], rgbColour[2]);
delay(5);
}
}
}
void setColourRgb(unsigned int red, unsigned int green, unsigned int blue) {
analogWrite(redPin, red);
analogWrite(greenPin, green);
analogWrite(bluePin, blue);
}
const int redPin = 11;

 

Comments

Popular posts from this blog

IoT - LPG Gas Sensor Logging with NodeMCU and Thingspeak.

In this tutorial, will learn, how to interface MQ-5 Module with Node Mcu(ESP8266).

The Grove - Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer.


Components Required
NodeMcu(ESP8266) MQ-5 LPG SENSOR Module Few male to female connecting wires Breadboard  Follow the image below for circuit connection reference:-
After making the circuit dump the code given below:-

// Karkhana Report
// Analyse the volume of the gas using thingspeak.com
// Hardware: NodeMCU,MQ-5

#include <ESP8266WiFi.h>
String apiKey = "Enter the API key"; // Enter your Write API key from ThingSpeak
const char *ssid = "Enter ssid"; // replace with your wifi ssid and wpa2 key
const char *pass = "Enter password";
const char* server = &qu…

Servo Motor Control using ESP8266 and Blynk App

Hey folks, 
In this tutorial we will learn how to interface Servo motor with NodeMcu(ESP8266)module and operate it with the Blynk app. Servos are controlled by sending an electrical pulse of variable width, or pulse width modulation (PWM), through the control wire. There is a minimum pulse, a maximum pulse, and a repetition rate. A servo motor can usually only turn 90° in either direction for a total of 180° movement.
   Follow the image below for circuit connection reference. In this circuit, we have connected the output pin to the D0 pin of the NodeMcu module. If want to control the servo motor manually then connect a 10K potetiometer . The 10K potentiometer will work as a voltage divisor, changing the analog input level on  NodeMCU (A0) from 0 to 3.3V. Internally, the 10 bits ADC (Analog-Digital converter) will generate a digital value (from 0 to 1023), the PotReading, equivalent to the analog voltage input.
After making the circuit dump the code given below.
/*NodeMCU */
#include <ESP…

IoT - Humidity and Temperature Logging using NodeMCU and ThingSpeak

Hey Folks,
In this tutorial, we will learn, how to interface DHT 11 with Node Mcu(ESP8266).
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).




Components Required
NodeMcu(ESP8266) DHT 11 SENSOR Few male to female connecting wires Breadboard
Follow the image below for circuit connection reference.
In this circuit, we have connected the output pin to the D3 pin of the NodeMcu module and NC pin remain disconnected. After making the circuit dump the code given below.
// Karkhana Report
// temperature and humidity data using thingspeak.com
// Hardware: NodeMCU,DHT11
#include <DHT.h> // Including library for dht
#include <ESP8266WiFi.h>
String apiKey = "THINGSPEAK API KEY"; // Enter your Write API key from ThingSpeak
const char *ssid = "ENTER YOUR SSID"; // replace with your wifi ssid a…