Skip to main content

Interfacing Of Switch (Push-Button) With ATMEGA16 Using AVR Studio

In this tutorial, we will learn how to interface a switch(push button) with ATMEGA16 using AVR studio.In previous video we learnt how to interface LEDs with ATMEGA16 using AVR studio.
The push-button is a component that connects two points in a circuit when you press it. The example turns on an LED when you press the button.Here we have connected two push button to PORT C in  PC0 & PC1.And for LEDs connection please refer my previous blog.
Link-  http://sudolearn.blogspot.in/2017/05/getting-started-with-embedded-system.html
Components Required:-
  • AVR Controller(Atmega16)
  • LEDs
  • Push Button
  • Connecting Wires
  • USBASP Programmer
Dump the following code after connection  and select chip ATMEGA 16.
#include<avr/io.h>
#include<util/delay.h>

void main()
 {
   DDRB=0b11111111;
   int S1;
   int S2;
 
   while(1)
   {
    S1=PINC&0b00000001;
    S2=PINC&0b00000010;
    if(S1==0b00000001)
    {
     PORTB=0b00000001;
     _delay_ms(100);
     }
     if(S2==0b00000010)
    {
     PORTB=0b00000010;
     _delay_ms(100);
     }
   }
   }



 After generating the hex file from AVR Studio, flash it in the chip and the following output can be seen.




                                                                                                                 -Thank You


Thinking?


Join our hands-on training courses.
To know more visit us at   http://www.sudolearn.com/

Comments

Popular posts from this blog

IoT - LPG Gas Sensor Logging with NodeMCU and Thingspeak.

In this tutorial, will learn, how to interface MQ-5 Module with Node Mcu(ESP8266).

The Grove - Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer.


Components Required
NodeMcu(ESP8266) MQ-5 LPG SENSOR Module Few male to female connecting wires Breadboard  Follow the image below for circuit connection reference:-
After making the circuit dump the code given below:-

// Karkhana Report
// Analyse the volume of the gas using thingspeak.com
// Hardware: NodeMCU,MQ-5

#include <ESP8266WiFi.h>
String apiKey = "Enter the API key"; // Enter your Write API key from ThingSpeak
const char *ssid = "Enter ssid"; // replace with your wifi ssid and wpa2 key
const char *pass = "Enter password";
const char* server = &qu…

IoT - Humidity and Temperature Logging using NodeMCU and ThingSpeak

Hey Folks,
In this tutorial, we will learn, how to interface DHT 11 with Node Mcu(ESP8266).
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).




Components Required
NodeMcu(ESP8266) DHT 11 SENSOR Few male to female connecting wires Breadboard
Follow the image below for circuit connection reference.
In this circuit, we have connected the output pin to the D3 pin of the NodeMcu module and NC pin remain disconnected. After making the circuit dump the code given below.
// Karkhana Report
// temperature and humidity data using thingspeak.com
// Hardware: NodeMCU,DHT11
#include <DHT.h> // Including library for dht
#include <ESP8266WiFi.h>
String apiKey = "THINGSPEAK API KEY"; // Enter your Write API key from ThingSpeak
const char *ssid = "ENTER YOUR SSID"; // replace with your wifi ssid a…

Servo Motor Control using ESP8266 and Blynk App

Hey folks, 
In this tutorial we will learn how to interface Servo motor with NodeMcu(ESP8266)module and operate it with the Blynk app. Servos are controlled by sending an electrical pulse of variable width, or pulse width modulation (PWM), through the control wire. There is a minimum pulse, a maximum pulse, and a repetition rate. A servo motor can usually only turn 90° in either direction for a total of 180° movement.
   Follow the image below for circuit connection reference. In this circuit, we have connected the output pin to the D0 pin of the NodeMcu module. If want to control the servo motor manually then connect a 10K potetiometer . The 10K potentiometer will work as a voltage divisor, changing the analog input level on  NodeMCU (A0) from 0 to 3.3V. Internally, the 10 bits ADC (Analog-Digital converter) will generate a digital value (from 0 to 1023), the PotReading, equivalent to the analog voltage input.
After making the circuit dump the code given below.
/*NodeMCU */
#include <ESP…